Hardware Programmers Software Courses Books Accessories Development Services Distributors Subscribe Contact Login



Programming Accessories
PASBW for SpyBiWire
JFPC JTAG to FPC Adapter
JTAG+
SVSPLUG
SVSWAFER
SB6V 6v Power Adapter

SoftBaugh Custom LCDs
SBLCDA2
SBLCDA2T
SBLCDA4
SBLCDA8
SBLCDA8T

RF Module Accessories
HMRF1611

Breadboard Accessories
B33V
BRS232
BAAA
SLBB

Cables and Wires
CBL25
CBLUSB
CBLBSL
CBLJTAG
CBLI2C
PWIRE
 

Click on the picture to enlarge.

Pricing
Ordering
Related Items
Downloads
FAQs
Feedback

 

Our $9 JFPC adapter allows you to program small boards via the Flexible-Printed-Circuit interface using any MSP430 JTAG programming source.

It features:

  • Converts MSP430 JTAG pinout to the FPC pinout
  • Includes a 2" FPC interface cable
  • 8-pin interface
  • Compatible with Hirose FH10A-8S-1SHB

This item has been discontinued and may no longer be ordered.

Related Items

  • Get the FETP for parallel port JTAG programming.
  • Get the USBP for USB port JTAG programming
  • Get the ISOFETP for parallel port JTAG programming with 1000v isolation for power-mains projects.

back to top

Downloads

JFPC Schematic (PDF)

back to top

FAQs

Q1: I need a RoHS version of the mating connector. Can you suggest a vendor?
A1: Use Oupiin 2434-08TD1T (www.oupiin.com) for top mount, or 2434-08TD2T for bottom mount. By the time you read this all of these connectors you purchase from Oupiin will be RoHS.

Q2: Since you are out of JFPCs, and have permanently discontinued them, how can I make my own with the FPC connector you sent us?
A2: Refer to the JFPC schematic in the downloads section above, and follow the table below:

Signal FPC Pin IDC Cable Wire
VCC 1 2
TEST 2 8
GND 3 9
TCK 4 7
TMS 5 5
TDI 6 3
TDO/TDI 7 1 (Red)
RST/NMI 8 11


Place the FPC connector on a table with the pins on the table and pointing away from you, as shown in the JFPC picture at the top of this page. The connector in the picture is brown with a white slide, but the connector we sent you is tan with a brown slide.

In this configuration the brown slide will be pointing toward you and against the table (brown-down). Pin 1 is the pin on the left.

On the 14-pin IDC JTAG cable, pin 1 is red.

back to top

Leave Feedback

As SoftBaugh continues efforts to increase features, along with ease of use, we find and consider feedback and suggestions essential to creating a better product for the customer.

Please note that if your intent is to receive technical support, or you if have general questions regarding this item, it is best to contact SoftBaugh directly, by phone or e-mail.

Feedback Form

back to top

Return Policy:
We will gladly accept returns on products as long as you notify us for an RMA number within 30-days and the items are returned in a re-saleable condition. Non-defective returned products are subject to a 20% restocking fee. Items damaged due to misuse are not returnable.

back to top

Handling Fee: Unless otherwise specified, SoftBaugh orders under $100.00 USD will be subject to a $10.00 USD handling fee.

Signature Proof of Delivery Required: We require a signature for all shipments. If you wish to waive the signature requirement, please mention it in the order comments. If you choose to waive the signature you assume all responsibility for receipt of the shipment.

Restocking Fee: All non-defective returns are subject to a 20% restocking fee. Shipping charges are not refundable. Product must be unopened in original packaging and suitable for resale. Products held for over 30 days or returned without a Return Material Authorization will not be accepted. Items damaged due to customer mishandling or misuse are not returnable. Software is not returnable.

Customers outside US: Due to the high cost of sending and accepting wire transfers, any orders paid by wire will be subject to a $40 wire fee. We accept checks at no additional charge by mail in US currency, or in foreign currency at the applicable current exchange rate. Please state your payment preference in the order comments. We require payment on all international orders before shipping.

Credit cards: We accept American Express, Visa, and MasterCard. If you wish to pay using one of these credit card types, fill out the form on the confirmation email you receive after placing your order and fax it back to us. International customers paying by credit card do not incur a wire fee.

Trademark notices: MSP430 and C2000 and specific MSP430 and C2000 part numbers are trademarks of Texas Instruments. EW430, IAR, IAR Systems, IAR Embedded Workbench, IAR MakeApp, C-SPY, visualSTATE, From Idea to Target and IAR KickStart Kit are trademarks or registered trademarks owned by IAR Systems AB. SoftBaugh and the SoftBaugh logo are registered trademarks of SoftBaugh, Inc. SoftBaugh board nomenclature and LCD part numbers are the trademark of SoftBaugh, Inc. Zigbee is the trademark of the Zigbee Alliance.

 
hardwareprogrammerssoftwarecoursesbooksaccessoriesservicesdistributorssubscribecontact
 
© 2001 - 2009 SoftBaugh, Inc. All rights reserved.